sane-dc210.5



sane-dc210(5)            SANE Scanner Access Now Easy            sane-dc210(5)


NAME

       sane-dc210 - SANE backend for Kodak DC210 Digital Camera


DESCRIPTION

       The  sane-dc210  library  implements  a  SANE (Scanner Access Now Easy)
       backend that provides access to the Kodak DC210  camera.  THIS  IS  EX-
       TREMELY ALPHA CODE!  USE AT YOUR OWN RISK!!


DEVICE NAMES

       The  current  version  of the backend only allows one camera to be con-
       nected.  The device name is always "0".


CONFIGURATION

       The contents of the dc210.conf specify the serial port and baud rate to
       use.  The baud rate specifies the maximum rate to use while downloading
       pictures.  (The camera is always  initialized  using  9600  baud,  then
       switches  to  the higher rate).  On my 90MHz Pentium, I usually have no
       problems downloading at 115200 baud as long as the system is not exces-
       sively busy and the "interrupt-unmask flag" is set in  the  IDE  driver
       (hdparm -u1).  Supported baud rates are: 9600, 19200, 38400, 57600, and
       115200.

       The  dumpinquiry  line  causes  some information about the camera to be
       printed.

       cmdrespause specifies how many usec (1,000,000ths of a second) to  wait
       between  writing the command and reading the result. 125000 seems to be
       the lowest I could go reliably.

       breakpause specifies how many usec (1,000,000ths of a  second)  between
       sending the "back to default" break and sending commands.

       Empty  lines  and  lines  starting with a hash mark (#) are ignored.  A
       sample configuration file is shown below:

              port=/dev/ttyS0
              # this is a comment
              baud=115200
              dumpinquiry
              cmdrespause=125000
              breakpause=1000000


FILES

       /usr/local/etc/sane.d/dc210.conf
              The  backend  configuration  file  (see  also   description   of
              SANE_CONFIG_DIR below).

       /usr/local/lib/sane/libsane-dc210.a
              The static library implementing this backend.

       /usr/local/lib/sane/libsane-dc210.so
              The shared library implementing this backend (present on systems
              that support dynamic loading).


ENVIRONMENT

       SANE_CONFIG_DIR
              This environment variable specifies the list of directories that
              may contain the configuration file.  On *NIX systems, the direc-
              tories are separated by a colon (`:'), under OS/2, they are sep-
              arated  by a semi-colon (`;').  If this variable is not set, the
              configuration file  is  searched  in  two  default  directories:
              first,  the current working directory (".") and then in /usr/lo-
              cal/etc/sane.d.  If the value of the environment  variable  ends
              with  the directory separator character, then the default direc-
              tories are searched after the explicitly specified  directories.
              For example, setting SANE_CONFIG_DIR to "/tmp/config:" would re-
              sult in directories tmp/config, ., and /usr/local/etc/sane.d be-
              ing searched (in this order).

       SANE_DEBUG_DC210
              If the library was compiled with debugging support enabled, this
              environment  variable controls the debug level for this backend.
              A value of 128 requests maximally copious debug output;  smaller
              levels reduce verbosity.


SEE ALSO

       sane(7)


AUTHOR

       Brian J. Murrell

       This  backend  is  based  somewhat on the dc25 backend included in this
       package by Peter Fales.

       The manpage was copied from the dc25 backend  and  somewhat  edited  by
       Henning Meier-Geinitz.


BUGS

       Known bugs/limitations are: ?

       More  general  comments,  suggestions, and inquiries about frontends or
       SANE  should  go   to   the   SANE   Developers   mailing   list   (see
       http://www.sane-project.org/mailing-lists.html  for details).  You must
       be subscribed to the list, otherwise your mail won't  be  sent  to  the
       subscribers.

                                  11 Jul 2008                    sane-dc210(5)

Man(1) output converted with man2html