Mustek BearPaw 2448 CU Pro
USB
0x055f
0x0408
Controller: SQ113C (Service & Quality, www.sq.com.tw) - probably contains embeded 8032 or something like this. Memory: HY57V161610 - Hynix 1Mx16 synchronous? DRAM A/D: Holtek HT82V36 - one channel(enough for CIS) A/D with serial configuration iface http://www.holtek.com.tw/pdf/computer/82v36.pdf W27C520 - 64k EEPROM, so no need for firmware upload it seems. AIC1563CS - DC/DC converter probably for higher voltage generation L6219 - well known stepper motor controller.
Maybe this scanner will be supported by the Mustek USB2 backend later.
Similar to the Mustek BearPaw 2448TA Pro, but uses CIS instead of CCD.
On the case of the scanner the following is written: "BearPaw 2448CU Pro MODEL NUMBER: BP 2400CU Plus"
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=055f ProdID=0408 Rev= 1.00
S: Manufacturer=Hewlett-Packard.
S: Product=USB2.0 Scanner
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=3ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=055f ProdID=0408 Rev= 1.00
S: Manufacturer=Hewlett-Packard.
S: Product=USB2.0 Scanner
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=500us
<device descriptor of 0x055f/0x0408 at 004:002 (Hewlett-Packard.
hp scanjet )>
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x055F
idProduct 0x0408
bcdDevice 1.00
iManufacturer 1 (Hewlett-Packard. )
iProduct 2 (hp scanjet )
iSerialNumber 0 ()
bNumConfigurations 1
<configuration 0>
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0 ()
bmAttributes 192 (Self-powered)
MaxPower 100 mA
<interface 0>
<altsetting 0>
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255
bInterfaceSubClass 255
bInterfaceProtocol 255
iInterface 0 ()
<endpoint 0>
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 (out 0x01)
bmAttributes 2 (bulk)
wMaxPacketSize 512
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 1>
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 (in 0x02)
bmAttributes 2 (bulk)
wMaxPacketSize 512
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 2>
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 (in 0x03)
bmAttributes 3 (interrupt)
wMaxPacketSize 1
bInterval 3 ms
bRefresh 0
bSynchAddress 0
<trying to find out which USB chip is used>
checking for GT-6801 ...
this is not a GT-6801 (bDeviceClass = 0)
checking for GT-6816 ...
this is not a GT-6816 (bcdUSB = 0x200)
checking for MA-1017 ...
this is not a MA-1017 (bDeviceClass = 0, bInterfaceClass = 255)
checking for MA-1015 ...
this is not a MA-1015 (bDeviceClass = 0)
checking for MA-1509 ...
this is not a MA-1509 (bDeviceClass = 0)
checking for LM983[1,2,3] ...
this is not a LM983x (bcdUSB = 0x200)
checking for GL646 ...
this is not a GL646 (bDeviceClass = 0, bInterfaceClass = 255)
checking for GL646_HP ...
this is not a GL646_HP (bDeviceClass = 0, bInterfaceClass = 255)
checking for GL660+GL646 ...
this is not a GL660+GL646 (bDeviceClass = 0, bInterfaceClass = 255)
checking for GL841 ...
this is not a GL841 (bDeviceClass = 0, bInterfaceClass = 255)
checking for ICM532B ...
check 1, this is not a ICM532B (bDeviceClass = 0, bInterfaceClass = 255)
<Couldn't determine the type of the USB chip>
found USB scanner (vendor=0x055f [Hewlett-Packard. ], product=0x0408 [hp scanjet ]) at libusb:004:002
If anything is wrong or missing on this page please file a bug report or use the the form for adding an unsupported device.
If you own an unsupported scanner, please send as much information as possible. Especially the output of sane-find-scanner -v -v and/or cat /proc/scsi/scsi (for SCSI scanners) or cat /proc/bus/usb/devices (for USB scanners) can help. If you dare to open the scanner, have a look at the text that's printed on the chips. That may help to identify the chipset. If you know that the scanner is similar to another one (e.g. supported by the same Windows driver), please also mention this fact.
Are you a manufacturer or vendor of scanners and one of your scanners is not supported by SANE yet? In this case please have a look at our information for manufacturers.