Scanners not supported by SANE

Manufacturer and model

Lexmark X1110 (?)
Lexmark X1130
Lexmark X1140 (?)
Lexmark X1150
Lexmark X1170 (?)
Lexmark X1180
Lexmark X1185

Bus type

USB

Vendor ID

Vendor=043d

Product ID

ProdID=007c

Chipset

Realtek RTS8852B

X1150:
Board Number  BJ4150M02001  Ver A-7
2 large processors :
Realtek RTS8852B-03  37012Q1  327F      - PC-Based MFP Controller Chip ( close relative to .)
Lexmark 18K0205      330B31V  ARM       - Printer controller?

3 smaller ICs:
SN105082 37AC4LT  14D0205               Silicon Controlled Rectifier
BD6775   329      H91                   NPN Darlington Transistor
24C01W6  B326L                          Serial EEPROM

Comments

At least the Lexmark X1185 is now supported by the lexmark backend. Maybe the other X11.. scanners also work? Please tell us about your results (send mail to sane-devel@alioth-lists.debian.net).

As all these devices use the same id, probably they have the same hardware. Under Windows the X1130 uses the same driver as the X1150 does (and all X1100 series). The printer-scanner kit contains a usb hub inside, for the two devices: Scanner and Printer. See also the devices output of the X1130 below. Printer works with Lexmark z600 driver.

Abbout the X1150: All in one job. Printer works fine with the z600 driver. Info on the scanner chip (well the closes relative I can find) can be found here.

Output of /proc/bus/usb/devices or sane-find-scanner -v -v

X1130:
(internal hub)
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12  MxCh= 2
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=043d ProdID=007a Rev= 1.00
S:  Manufacturer=Lexmark
S:  Product=USB Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  8mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=255ms

(printer)
T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=043d ProdID=007c Rev= 1.00
S:  Manufacturer=Lexmark
S:  Product=X1100 Series
S:  SerialNumber=5509812
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=   8 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=250ms

(scanner)
T:  Bus=01 Lev=02 Prnt=03 Port=01 Cnt=02 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=043d ProdID=007b Rev= 1.00
S:  Manufacturer=Lexmark
S:  Product=Lexmark X1100 Series
S:  SerialNumber=5509812
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  4mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp
E:  Ad=05(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=  16 Ivl=0ms

X1150:
T:  Bus=02 Lev=02 Prnt=06 Port=00 Cnt=01 Dev#=  7 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=043d ProdID=007c Rev= 1.00
S:  Manufacturer=Lexmark
S:  Product=X1100 Series
S:  SerialNumber=5003470
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=   8 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=250ms

X1150:
<device descriptor of 0x043d/0x007c at 002:004>
bLength               18
bDescriptorType       1
bcdUSB                1.10
bDeviceClass          0
bDeviceSubClass       0
bDeviceProtocol       0
bMaxPacketSize0       8
idVendor              0x043D
idProduct             0x007C
bcdDevice             1.00
iManufacturer         1 ((null))
iProduct              2 ((null))
iSerialNumber         7 ((null))
bNumConfigurations    1
 <configuration 0>
 bLength              9
 bDescriptorType      2
 wTotalLength         39
 bNumInterfaces       1
 bConfigurationValue  1
 iConfiguration       6 ((null))
 bmAttributes         224 (Self-poweredRemote Wakeup)
 MaxPower             0 mA
  <interface 0>
   <altsetting 0>
   bLength            9
   bDescriptorType    4
   bInterfaceNumber   0
   bAlternateSetting  0
   bNumEndpoints      3
   bInterfaceClass    255
   bInterfaceSubClass 0
   bInterfaceProtocol 255
   iInterface         9 ((null))
    <endpoint 0>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x81 (in 0x01)
    bmAttributes      2 (bulk)
    wMaxPacketSize    64
    bInterval         0 ms
    bRefresh          0
    bSynchAddress     0
    <endpoint 1>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x02 (out 0x02)
    bmAttributes      2 (bulk)
    wMaxPacketSize    8
    bInterval         0 ms
    bRefresh          0
    bSynchAddress     0
    <endpoint 2>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x83 (in 0x03)
    bmAttributes      3 (interrupt)
    wMaxPacketSize    1
    bInterval         250 ms
    bRefresh          0
    bSynchAddress     0

<trying to find out which USB chip is used>
    checking for GT-6801 ...
    this is not a GT-6801 (bDeviceClass = 0)
    checking for GT-6816 ...
    this is not a GT-6816 (bNumEndpoints = 3)
    checking for MA-1017 ...
    this is not a MA-1017 (bDeviceClass = 0, bInterfaceClass = 255)
    checking for MA-1015 ...
    this is not a MA-1015 (bDeviceClass = 0)
    checking for MA-1509 ...
    this is not a MA-1509 (bDeviceClass = 0)
    checking for LM983[1,2,3] ...
    this is not a LM983x (bEndpointAddress = 0x81, bmAttributes = 0x2, wMaxPacketSize = 0x40, bInterval = 0x0)
    checking for GL646 ...
    this is not a GL646 (bDeviceClass = 0, bInterfaceClass = 255)
    checking for GL660+GL646 ...
    this is not a GL660+GL646 (bDeviceClass = 0, bInterfaceClass = 255)
<Couldn't determine the type of the USB chip>

found USB scanner (vendor=0x043d, product=0x007c) at libusb:002:004


X1180:
T:  Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=043d ProdID=007c Rev= 1.00
S:  Manufacturer=Lexmark
S:  Product=X1100 Series
S:  SerialNumber=3277660
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=   8 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=250ms
    

Want to add or correct information?

If anything is wrong or missing on this page please file a bug report or use the the form for adding an unsupported device.

If you own an unsupported scanner, please send as much information as possible. Especially the output of sane-find-scanner -v -v and/or cat /proc/scsi/scsi (for SCSI scanners) or cat /proc/bus/usb/devices (for USB scanners) can help. If you dare to open the scanner, have a look at the text that's printed on the chips. That may help to identify the chipset. If you know that the scanner is similar to another one (e.g. supported by the same Windows driver), please also mention this fact.

Information for Manufacturers

Are you a manufacturer or vendor of scanners and one of your scanners is not supported by SANE yet? In this case please have a look at our information for manufacturers.

Links


SANE homepage
Contact