Scanners not supported by SANE

Manufacturer and model

Canon CanoScan 9950F

Bus type

USB, IEEE-1394

Vendor ID

0x04a9

Product ID

0x2219

Chipset

ST6810PBA

Comments

With transparency adaptor. Supports 4800 x 9600dpi and 48bit colour. Scans +30x35mm, 120 roll and 4x5" transparencies. USB and firewire. Similar to Canon 9900F.

On PCB there are also:

A low quality image of the entire PCB is visible here

Output of /proc/bus/usb/devices or sane-find-scanner -v -v or lsusb -vv

T:  Bus=04 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=04a9 ProdID=2219 Rev= 3.01
S:  Manufacturer=Canon
S:  Product=Scanner
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 10mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   1 Ivl=16ms

This is sane-find-scanner from sane-backends 1.0.15
<device descriptor of 0x04a9/0x2219 at 004:005 (Canon Scanner)>
bLength               18
bDescriptorType       1
bcdUSB                2.00
bDeviceClass          255
bDeviceSubClass       255
bDeviceProtocol       255
bMaxPacketSize0       64
idVendor              0x04A9
idProduct             0x2219
bcdDevice             3.01
iManufacturer         1 (Canon)
iProduct              2 (Scanner)
iSerialNumber         0 ()
bNumConfigurations    1
 <configuration 0>
 bLength              9
 bDescriptorType      2
 wTotalLength         39
 bNumInterfaces       1
 bConfigurationValue  1
 iConfiguration       0 ()
 bmAttributes         192 (Self-powered)
 MaxPower             10 mA
  <interface 0>
   <altsetting 0>
   bLength            9
   bDescriptorType    4
   bInterfaceNumber   0
   bAlternateSetting  0
   bNumEndpoints      3
   bInterfaceClass    255
   bInterfaceSubClass 255
   bInterfaceProtocol 255
   iInterface         0 ()
    <endpoint 0>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x81 (in 0x01)
    bmAttributes      2 (bulk)
    wMaxPacketSize    512
    bInterval         0 ms
    bRefresh          0
    bSynchAddress     0
    <endpoint 1>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x02 (out 0x02)
    bmAttributes      2 (bulk)
    wMaxPacketSize    512
    bInterval         0 ms
    bRefresh          0
    bSynchAddress     0
    <endpoint 2>
    bLength           7
    bDescriptorType   5
    bEndpointAddress  0x83 (in 0x03)
    bmAttributes      3 (interrupt)
    wMaxPacketSize    1
    bInterval         8 ms
    bRefresh          0
    bSynchAddress     0

<trying to find out which USB chip is used>
    checking for GT-6801 ...
    this is not a GT-6801 (bcdUSB = 0x200)
    checking for GT-6816 ...
    this is not a GT-6816 (bDeviceClass = 255, bInterfaceClass = 255)
    checking for GT-8911 ...
    this is not a GT-8911 (check 1, bDeviceClass = 255, bInterfaceClass = 255)
    checking for MA-1017 ...
    this is not a MA-1017 (bDeviceClass = 255, bInterfaceClass = 255)
    checking for MA-1015 ...
    this is not a MA-1015 (bcdUSB = 0x200)
    checking for MA-1509 ...
    this is not a MA-1509 (bcdUSB = 0x200)
    checking for LM983[1,2,3] ...
    this is not a LM983x (bcdUSB = 0x200)
    checking for GL646 ...
    this is not a GL646 (bDeviceClass = 255, bInterfaceClass = 255)
    checking for GL646_HP ...
    this is not a GL646_HP (bcdUSB = 0x200)
    checking for GL660+GL646 ...
    this is not a GL660+GL646 (bDeviceClass = 255, bInterfaceClass = 255)
    checking for GL841 ...
    this is not a GL841 (reg 0x38 != 0x15)
    checking for ICM532B ...
    this is not a ICM532B (check 2, bcdUSB = 0x200)
<Couldn't determine the type of the USB chip>

found USB scanner (vendor=0x04a9 [Canon], product=0x2219 [Scanner]) at libusb:004:005

Want to add or correct information?

If anything is wrong or missing on this page please file a bug report or use the the form for adding an unsupported device.

If you own an unsupported scanner, please send as much information as possible. Especially the output of sane-find-scanner -v -v and/or cat /proc/scsi/scsi (for SCSI scanners) or cat /proc/bus/usb/devices (for USB scanners) can help. If you dare to open the scanner, have a look at the text that's printed on the chips. That may help to identify the chipset. If you know that the scanner is similar to another one (e.g. supported by the same Windows driver), please also mention this fact.

Information for Manufacturers

Are you a manufacturer or vendor of scanners and one of your scanners is not supported by SANE yet? In this case please have a look at our information for manufacturers.

SANE homepage
Contact