Ans again...Mustek SE 12000 SP

From: minstrel@bigfoot.de
Date: Sat Jan 22 2000 - 03:36:16 PST

  • Next message: Christian Fughe: "Scanmaker II or IIxe with parallel port interface ?"

    Hi there!
    Is there any chance for the future to get this scanner work?
    I`m running Kernel 2.2.13 at SuSE 6.3
    dmesg tells me:
    scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
    scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
    scsi1: Configuring BusLogic Model BT-930 PCI Ultra SCSI Host Adapter
    scsi1: Firmware Version: 5.02, I/O Address: 0xE000, IRQ
    Channel: 11/Level
    scsi1: PCI Bus: 0, Device: 11, Address: 0xEA001000, Host Adapter SCSI
    ID: 7
    scsi1: Parity Checking: Enabled, Extended Translation: Enabled
    scsi1: Synchronous Negotiation: Fast, Wide Negotiation: Disabled
    scsi1: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
    scsi1: Driver Queue Depth: 255, Scatter/Gather Limit: 128 segments
    scsi1: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
    scsi1: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
    scsi1: SCSI Bus Termination: Enabled, SCAM: Enabled, Level 1
    scsi1: *** BusLogic BT-930 Initialized Successfully ***
    scsi1 : BusLogic BT-930
    scsi : 2 hosts.
      Vendor: SCANNER Model: Rev: V100
      Type: Scanner ANSI SCSI revision: 01 CCS
    Detected scsi generic sgc at scsi1, channel 0, id 6, lun 0
    scsi1: Target 6: Queue Depth 3, Asynchronous

    i changed
    :model "SCANNER V100"
    :comment "1 pass; (f/w == 38.00; scsi id XC06 S12IDWM123797A)"
    in mustek.desc

    and " XC06" for " C06" in mustek.c

    but still
     SANE_DEBUG_MUSTEK=3 scanimage -d mustek
    [sanei_init_debug]: Setting debug level of mustek to 3.
    [mustek] sane_init: strip-height set to 1 inches
    [mustek] attach: opening /dev/sgc as scsi device
    [mustek] attach: sending INQUIRY
    [mustek] scsi_wait_ready: sending TEST_UNIT_READY
    [mustek] attach: firmware revision 38.00
    [mustek] attach: unknown model `XC06 S12IDWM123797A'
    [mustek] attach: opening /dev/scanner as scsi device
    [mustek] attach: sending INQUIRY
    [mustek] scsi_wait_ready: sending TEST_UNIT_READY
    [mustek] attach: firmware revision 38.00
    [mustek] attach: unknown model `XC06 S12IDWM123797A'
    [mustek] attach: opening /dev/scanner as scsi device
    [mustek] attach: sending INQUIRY
    [mustek] scsi_wait_ready: sending TEST_UNIT_READY
    [mustek] attach: firmware revision 38.00
    [mustek] attach: unknown model `XC06 S12IDWM123797A'
    scanimage: open of device mustek failed: Invalid argument

    scanimage: no SANE devices found
    find-scanner: found scanner "SCANNER V100" at device /dev/scanner
    find-scanner: found scanner "SCANNER V100" at device /dev/sg2
    find-scanner: found scanner "SCANNER V100" at device /dev/sgc

    Thanks for helping,
                                  
    Uwe Hof
    Im Gunzetal 35
    57319 Bad Berleburg
    Registered Linux-User #115895 

    --
Source code, list archive, and docs: http://www.mostang.com/sane/
To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com

    This archive was generated by hypermail 2b29 : Sat Jan 22 2000 - 02:36:38 PST