Microtek ScanMaker4
Model # MRS-1200TP
1999
New Scanner... Didn't see it mentioned at all on your page, so here are
the output files from various commands:
The following environment variables were exported as follows:
declare -x SANE_DEBUG_DLL="128"
declare -x SANE_DEBUG_MICROTEK="128"
declare -x SANE_DEBUG_MICROTEK2="128"
declare -x SANE_DEBUG_SANEI_SCSI="128"
The following is an excerpt from dmesg:
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 11/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.17/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: IBM Model: DRVS09V Rev: 00E5
Type: Direct-Access ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: TANDEM Model: 4255-1 Rev: 5t5t
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: TANDEM Model: 4255-1 Rev: 5t5t
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: TANDEM Model: 4255-1 Rev: 5t5t
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0
Vendor: RICOH Model: MP6200S Rev: 2.03
Type: CD-ROM ANSI SCSI revision: 02
Vendor: Microtek Model: ScanMaker IV Rev: 1.00
Type: Scanner ANSI SCSI revision: 02
scsi : detected 4 SCSI disks total.
--------------A4EBD338E85B73FC40C07220
Content-Type: text/plain; charset=us-ascii;
name="sane-microtek.output"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="sane-microtek.output"
[sanei_init_debug]: Setting debug level of dll to 128.
[dll] adding backend net
[dll] adding backend abaton
[dll] adding backend agfafocus
[dll] adding backend apple
[dll] adding backend artec
[dll] adding backend canon
[dll] adding backend coolscan
[dll] adding backend dmc
[dll] adding backend epson
[dll] adding backend hp
[dll] adding backend microtek
[dll] adding backend microtek2
[dll] adding backend mustek
[dll] adding backend pint
[dll] adding backend qcam
[dll] adding backend ricoh
[dll] adding backend s9036
[dll] adding backend sharp
[dll] adding backend snapscan
[dll] adding backend tamarack
[dll] adding backend umax
[dll] loading backend microtek
[dll] dlopen()ing `/usr/lib/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[sanei_init_debug]: Setting debug level of microtek to 128.
[microtek] sane_init: MICROTEK says hello! (v0.10.1)
[microtek] sane_init: config- #Uncomment following line to disable "clever precalibration" routines...
[microtek] sane_init: config- #noprecal
[microtek] sane_init: config- scsi * * Scanner
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] searched device is /dev/sgf
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804dd00
[sanei_scsi] sanei_scsi.issue: 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00h'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
[sanei_scsi] searched device is /dev/sgf
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804dd00
[sanei_scsi] sanei_scsi.issue: 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
[microtek] sane_init: config- /dev/scanner
[microtek] attach_scanner: /dev/scanner
[microtek] attach_scanner: opening /dev/scanner
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[microtek] attach_scanner: open failed
[microtek] sane_open
[microtek] sane_open: find device...
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804dd00
[sanei_scsi] sanei_scsi.issue: 0x804dd00
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
scanimage: open of device microtek:/dev/sgf failed: Invalid argument
[dll] exiting
[dll] calling backend `microtek's exit function
[microtek] sane_exit...
[microtek] sane_exit: MICROTEK says goodbye.
--------------A4EBD338E85B73FC40C07220
Content-Type: text/plain; charset=us-ascii;
name="sane-microtek2.output"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="sane-microtek2.output"
[sanei_init_debug]: Setting debug level of dll to 128.
[dll] adding backend net
[dll] adding backend abaton
[dll] adding backend agfafocus
[dll] adding backend apple
[dll] adding backend artec
[dll] adding backend canon
[dll] adding backend coolscan
[dll] adding backend dmc
[dll] adding backend epson
[dll] adding backend hp
[dll] adding backend microtek
[dll] adding backend microtek2
[dll] adding backend mustek
[dll] adding backend pint
[dll] adding backend qcam
[dll] adding backend ricoh
[dll] adding backend s9036
[dll] adding backend sharp
[dll] adding backend snapscan
[dll] adding backend tamarack
[dll] adding backend umax
[dll] loading backend microtek2
[dll] dlopen()ing `/usr/lib/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[sanei_init_debug]: Setting debug level of microtek2 to 128.
[microtek2] sane_init: Microtek2 (v0.6) says hello...
[microtek2] attach_one: name='# See sane-microtek2(5) for a description of the options
'
[microtek2] add_device_list: device='# See sane-microtek2(5) for a description of the options'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='
'
[microtek2] add_device_list: device=''
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='option dump 1
'
[microtek2] add_device_list: device='option dump 1'
[microtek2] attach_one: returning
[microtek2] attach_one: name='# option lightlid-35 on
'
[microtek2] add_device_list: device='# option lightlid-35 on'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='# option no-backtrack-option on
'
[microtek2] add_device_list: device='# option no-backtrack-option on'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='/dev/sgf
'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] attach: device='/dev/sgf'
[microtek2] scsi_inquiry: mi=0x804dbcc, device='/dev/sgf'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] scsi_req_enter: entered 0x804e508
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804e508
[sanei_scsi] sanei_scsi.issue: 0x804e508
[sanei_scsi] sanei_scsi_req_wait: read 41 bytes
[sanei_scsi] scsi_req_enter: entered 0x804e508
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804e508
[sanei_scsi] sanei_scsi.issue: 0x804e508
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek2] check_inquiry: mi=0x804dbcc
[microtek2] check_inquiry: Device is not a Microtek, but 'Microtek'
[microtek2] attach_one: returning
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] searched device is /dev/sgf
[microtek2] attach_one: name='/dev/sgf'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] add_device_list: device '/dev/sgf' already in list
[microtek2] attach_one: returning
[sanei_scsi] searched device is /dev/sgf
[microtek2] attach_one: name='/dev/sgf'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] add_device_list: device '/dev/sgf' already in list
[microtek2] attach_one: returning
[microtek2] sane_open: device='/dev/sgf'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] add_device_list: device '/dev/sgf' already in list
[microtek2] attach: device='/dev/sgf'
[microtek2] scsi_inquiry: mi=0x804dbcc, device='/dev/sgf'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] scsi_req_enter: entered 0x804e508
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804e508
[sanei_scsi] sanei_scsi.issue: 0x804e508
[sanei_scsi] sanei_scsi_req_wait: read 41 bytes
[sanei_scsi] scsi_req_enter: entered 0x804e508
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804e508
[sanei_scsi] sanei_scsi.issue: 0x804e508
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek2] check_inquiry: mi=0x804dbcc
[microtek2] check_inquiry: Device is not a Microtek, but 'Microtek'
scanimage: open of device microtek2:/dev/sgf failed: Error during device I/O
[dll] exiting
[dll] calling backend `microtek2's exit function
[microtek2] sane_exit:
[microtek2] sane_get_devices: local_only=0
[microtek2] sane_get_devices: sd_list_freed
[microtek2] sane_exit: MICROTEK2 says goodbye.
--------------A4EBD338E85B73FC40C07220
Content-Type: text/plain; charset=us-ascii;
name="scanimage-L.output"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="scanimage-L.output"
[sanei_init_debug]: Setting debug level of dll to 128.
[dll] adding backend net
[dll] adding backend abaton
[dll] adding backend agfafocus
[dll] adding backend apple
[dll] adding backend artec
[dll] adding backend canon
[dll] adding backend coolscan
[dll] adding backend dmc
[dll] adding backend epson
[dll] adding backend hp
[dll] adding backend microtek
[dll] adding backend microtek2
[dll] adding backend mustek
[dll] adding backend pint
[dll] adding backend qcam
[dll] adding backend ricoh
[dll] adding backend s9036
[dll] adding backend sharp
[dll] adding backend snapscan
[dll] adding backend tamarack
[dll] adding backend umax
[dll] loading backend umax
[dll] dlopen()ing `/usr/lib/sane/libsane-umax.so.1'
[dll] init: initializing backend `umax'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend tamarack
[dll] dlopen()ing `/usr/lib/sane/libsane-tamarack.so.1'
[dll] init: initializing backend `tamarack'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend snapscan
[dll] dlopen()ing `/usr/lib/sane/libsane-snapscan.so.1'
[dll] init: initializing backend `snapscan'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] scsi_req_enter: entered 0x804e340
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x804e340
[sanei_scsi] sanei_scsi.issue: 0x804e340
[sanei_scsi] sanei_scsi_req_wait: read 72 bytes
[dll] loading backend sharp
[dll] dlopen()ing `/usr/lib/sane/libsane-sharp.so.1'
[dll] init: initializing backend `sharp'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend s9036
[dll] dlopen()ing `/usr/lib/sane/libsane-s9036.so.1'
[dll] init: initializing backend `s9036'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend ricoh
[dll] dlopen()ing `/usr/lib/sane/libsane-ricoh.so.1'
[dll] init: initializing backend `ricoh'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend qcam
[dll] dlopen()ing `/usr/lib/sane/libsane-qcam.so.1'
[dll] init: initializing backend `qcam'
[dll] loading backend pint
[dll] load: couldn't find /usr/lib/sane/libsane-pint.so.1 (No such file or directory)
[dll] loading backend mustek
[dll] dlopen()ing `/usr/lib/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend microtek2
[dll] dlopen()ing `/usr/lib/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[sanei_init_debug]: Setting debug level of microtek2 to 128.
[microtek2] sane_init: Microtek2 (v0.6) says hello...
[microtek2] attach_one: name='# See sane-microtek2(5) for a description of the options
'
[microtek2] add_device_list: device='# See sane-microtek2(5) for a description of the options'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='
'
[microtek2] add_device_list: device=''
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='option dump 4
'
[microtek2] add_device_list: device='option dump 4'
[microtek2] attach_one: returning
[microtek2] attach_one: name='# option lightlid-35 on
'
[microtek2] add_device_list: device='# option lightlid-35 on'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='# option no-backtrack-option on
'
[microtek2] add_device_list: device='# option no-backtrack-option on'
[microtek2] add_device_list: Comment or empty line in microtek2.conf
[microtek2] attach_one: returning
[microtek2] attach_one: name='/dev/sgf
'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] attach: device='/dev/sgf'
[microtek2] scsi_inquiry: mi=0x80577f4, device='/dev/sgf'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] scsi_req_enter: entered 0x8058230
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8058230
[sanei_scsi] sanei_scsi.issue: 0x8058230
[sanei_scsi] sanei_scsi_req_wait: read 41 bytes
[inquiry]
120000006000
[sanei_scsi] scsi_req_enter: entered 0x8058230
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8058230
[sanei_scsi] sanei_scsi.issue: 0x8058230
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[inquiryresult]
060002025b0000004d6963726f74656b5363616e4d616b657220495620202020312e3030810000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[microtek2] dump_area: inquiryresult
0: 060002025b000000 4d6963726f74656b ....[... Microtek
16: 5363616e4d616b65 7220495620202020 ScanMake r IV
32: 312e303081000000 0000000000000000 1.00.... ........
48: 0000000000000000 0000000000000000 ........ ........
64: 0000000000000000 0000000000000000 ........ ........
80: 0000000000000000 0000000000000000 ........ ........
[microtek2] check_inquiry: mi=0x80577f4
[microtek2] check_inquiry: Device is not a Microtek, but 'Microtek'
[microtek2] attach_one: returning
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] searched device is /dev/sgf
[microtek2] attach_one: name='/dev/sgf'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] add_device_list: device '/dev/sgf' already in list
[microtek2] attach_one: returning
[sanei_scsi] searched device is /dev/sgf
[microtek2] attach_one: name='/dev/sgf'
[microtek2] add_device_list: device='/dev/sgf'
[microtek2] add_device_list: device '/dev/sgf' already in list
[microtek2] attach_one: returning
[microtek2] sane_get_devices: local_only=0
[microtek2] attach: device='/dev/sgf'
[microtek2] scsi_inquiry: mi=0x80577f4, device='/dev/sgf'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] scsi_req_enter: entered 0x8058230
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8058230
[sanei_scsi] sanei_scsi.issue: 0x8058230
[sanei_scsi] sanei_scsi_req_wait: read 41 bytes
[inquiry]
120000006000
[sanei_scsi] scsi_req_enter: entered 0x8058230
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8058230
[sanei_scsi] sanei_scsi.issue: 0x8058230
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[inquiryresult]
060002025b0000004d6963726f74656b5363616e4d616b657220495620202020312e3030810000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
[microtek2] dump_area: inquiryresult
0: 060002025b000000 4d6963726f74656b ....[... Microtek
16: 5363616e4d616b65 7220495620202020 ScanMake r IV
32: 312e303081000000 0000000000000000 1.00.... ........
48: 0000000000000000 0000000000000000 ........ ........
64: 0000000000000000 0000000000000000 ........ ........
80: 0000000000000000 0000000000000000 ........ ........
[microtek2] check_inquiry: mi=0x80577f4
[microtek2] check_inquiry: Device is not a Microtek, but 'Microtek'
[microtek2] sane_get_devices: attach status 'Error during device I/O'
[microtek2] sane_get_devices: returning
[dll] loading backend microtek
[dll] dlopen()ing `/usr/lib/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[sanei_init_debug]: Setting debug level of microtek to 128.
[microtek] sane_init: MICROTEK says hello! (v0.10.1)
[microtek] sane_init: config- #Uncomment following line to disable "clever precalibration" routines...
[microtek] sane_init: config- #noprecal
[microtek] sane_init: config- scsi * * Scanner
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] searched device is /dev/sgf
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x8060910
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8060910
[sanei_scsi] sanei_scsi.issue: 0x8060910
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00`'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
[sanei_scsi] searched device is /dev/sgf
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x8060910
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8060910
[sanei_scsi] sanei_scsi.issue: 0x8060910
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
[microtek] sane_init: config- /dev/sgf
[microtek] attach_scanner: /dev/sgf
[microtek] attach_scanner: opening /dev/sgf
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[microtek] attach_scanner: sending INQUIRY
[sanei_scsi] scsi_req_enter: entered 0x8060910
[sanei_scsi] sanei_scsi_req_wait: waiting for 0x8060910
[sanei_scsi] sanei_scsi.issue: 0x8060910
[sanei_scsi] sanei_scsi_req_wait: read 132 bytes
[microtek] id_microtek...
[microtek] id_microtek: not microtek: -32, -45, 0
[microtek] attach_scanner: device doesn't look like a Microtek scanner.[microtek] dump_suspect_inquiry...
=== SANE/Microtek backend v0.10.1 ===
========== Scanner Inquiry Block ========mm
06 00 02 02 5b 00 00 00 4d 69 63 72 6f 74 65 6b
53 63 61 6e 4d 61 6b 65 72 20 49 56 20 20 20 20
31 2e 30 30 81 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
========== Scanner Inquiry Report ==========
===== Scanner ID...
Device Type Code: 0x06
Model Code: 0x00
Vendor Name: 'Microtek' Model Name: 'ScanMaker IV '
Firmware Rev: '1.00'
SCSI F/W version: 0.0 Scanner F/W version: 0.2
Response data format: 0x02
[microtek] sane_get_devices
[dll] loading backend hp
[dll] dlopen()ing `/usr/lib/sane/libsane-hp.so.1'
[dll] init: initializing backend `hp'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend epson
[dll] dlopen()ing `/usr/lib/sane/libsane-epson.so.1'
[dll] init: initializing backend `epson'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend dmc
[dll] dlopen()ing `/usr/lib/sane/libsane-dmc.so.1'
[dll] init: initializing backend `dmc'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/camera' failed: No such file or directory
[dll] loading backend coolscan
[dll] dlopen()ing `/usr/lib/sane/libsane-coolscan.so.1'
[dll] init: initializing backend `coolscan'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend canon
[dll] dlopen()ing `/usr/lib/sane/libsane-canon.so.1'
[dll] init: initializing backend `canon'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend artec
[dll] dlopen()ing `/usr/lib/sane/libsane-artec.so.1'
[dll] init: initializing backend `artec'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend apple
[dll] dlopen()ing `/usr/lib/sane/libsane-apple.so.1'
[dll] init: initializing backend `apple'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend agfafocus
[dll] dlopen()ing `/usr/lib/sane/libsane-agfafocus.so.1'
[dll] init: initializing backend `agfafocus'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend abaton
[dll] dlopen()ing `/usr/lib/sane/libsane-abaton.so.1'
[dll] init: initializing backend `abaton'
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_init_debug]: Setting debug level of sanei_scsi to 128.
[sanei_scsi] sanei_scsi_open: open of `/dev/scanner' failed: Device not configured
[dll] loading backend net
[dll] dlopen()ing `/usr/lib/sane/libsane-net.so.1'
[dll] init: initializing backend `net'
[dll] exiting
[dll] calling backend `umax's exit function
[dll] calling backend `tamarack's exit function
[dll] calling backend `snapscan's exit function
[dll] calling backend `sharp's exit function
[dll] calling backend `s9036's exit function
[dll] calling backend `ricoh's exit function
[dll] calling backend `qcam's exit function
[dll] calling backend `pint's exit function
[dll] call to unsupported backend operation
[dll] calling backend `mustek's exit function
[dll] calling backend `microtek2's exit function
[microtek2] sane_exit:
[microtek2] sane_get_devices: local_only=0
[microtek2] sane_get_devices: sd_list_freed
[microtek2] sane_exit: MICROTEK2 says goodbye.
[dll] calling backend `microtek's exit function
[microtek] sane_exit...
[microtek] sane_exit: MICROTEK says goodbye.
[dll] calling backend `hp's exit function
[dll] calling backend `epson's exit function
[dll] calling backend `dmc's exit function
[dll] calling backend `coolscan's exit function
[dll] calling backend `canon's exit function
[dll] calling backend `artec's exit function
[dll] calling backend `apple's exit function
[dll] calling backend `agfafocus's exit function
[dll] calling backend `abaton's exit function
[dll] calling backend `net's exit function
--------------A4EBD338E85B73FC40C07220--
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com