Initially, I thought it would be...but then again
see below.
-- ++++++++++++++++++++++++++++++++++++++++++++++ Dave Neal Email Address - ?????? Phone w/ Voice Mail (505) 665-6471 Digital Pager - (505) 6659800 Pager ID 1048666 ++++++++++++++++++++++++++++++++++++++++++++++dneal @ cardinal.lanl.gov % /usr/local/bin/xscanimage -V xscanimage (sane) 1.0 dneal @ cardinal.lanl.gov % /usr/local/src/sane-1.00/tools/find-scanner # You may want to run this program as super-user to find all devices. # Once you found the scanner devices, be sure to adjust access # permissions as necessary.
find-scanner: found scanner "Nikon LS-2000 1.12" at device /dev/scanner find-scanner: found scanner "Nikon LS-2000 1.12" at device /dev/sgb dneal @ cardinal% scanimage -d coolscan:/dev/sgb scanimage: open of device coolscan:/dev/sgb failed: Invalid argument dneal @ cardinal.lanl.gov % ls -l /dev/sgb crwxrwxrwx 1 root sys 21, 1 May 5 1998 /dev/sgb dneal @ cardinal% uname -a Linux cardinal 2.2.5-ac6 #1 SMP Mon Apr 19 12:55:23 MDT 1999 i686 unknown dneal @ cardinal%
========================= portion of dmesg output ================================ RAM disk driver initialized: 16 RAM disks of 4096K size loop: registered device at major 7 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 (scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 10/0 (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs (scsi0) Downloading sequencer code... 407 instructions downloaded (scsi1) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 14/0 (scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs (scsi1) Warning - detected auto-termination (scsi1) Please verify driver detected settings are correct. (scsi1) If not, then please properly set the device termination (scsi1) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted (scsi1) during machine bootup. (scsi1) Cables present (Int-50 NO, Int-68 NO, Ext-68 NO) (scsi1) Downloading sequencer code... 419 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.13/3.2.4 <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.13/3.2.4 <Adaptec AIC-7880 Ultra SCSI host adapter> scsi : 2 hosts. Vendor: QUANTUM Model: VIKING II 4.5WLS Rev: 3506 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 (scsi0:0:0:0) Synchronous at 80.0 Mbyte/sec, offset 31. Vendor: Nikon Model: LS-2000 Rev: 1.12 Type: Scanner ANSI SCSI revision: 02 Detected scsi generic sgb at scsi1, channel 0, id 2, lun 0 Vendor: NEC Model: CD-ROM DRIVE:465 Rev: 1.03 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi1, channel 0, id 5, lun 0 (scsi1:0:5:0) Synchronous at 20.0 Mbyte/sec, offset 15. scsi : detected 1 SCSI cdrom 1 SCSI disk total. sr0: scsi3-mmc drive: 14x/32x cd/rw xa/form2 cdda tray Uniform CDROM driver Revision: 2.54 SCSI device sda: hdwr sector= 512 bytes. Sectors= 8910423 [4350 MB] [4.4 GB] Partition check: sda: sda1 sda2 sda3 sda4 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 44k freed Adding Swap: 130748k swap-space (priority -1) Adding Swap: 130748k swap-space (priority -2) 3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html eth0: 3Com 3c905B Cyclone 100baseTx at 0xec00, 00:c0:4f:79:f3:cd, IRQ 19 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface. MII transceiver found at address 24, status 782d. Enabling bus-master transmits and whole-frame receives.
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com