Mustek SE 12000SP, only in gray with SANE on SuSE 5.3 ?
I've just had a scanner - Mustek SE 12000SP (C06 S12IDW flatbed scanner)
- and I've plugged it on my SCSI-3 controller, a Tekram DC-390F.
When I use SANE (new version 1.0 - SuSE rpm), I can work only in Gray or
Lineart at the lowest resolution : 60 dpi.
If I try something else, I've got the following messages :
Error during read : Out of memory - (xscanimage in Xwindow)
or
sane_read: Out of memory - (scanimage in console mode)
My computer is fitted with 64 Mo SDRAM and 64 Mo of SWAP...
The scanner works fine under Micro$oft 95 but not on SuSE Linux 5.3 !
Does anyone has THE solution ?
I tried the following things :
1 - asking Dejanews -> nothing !
2 - reading SANE documentation with different tests on
/etc/sane.d/mustek.conf -> nothing !
3 - try swapoff -a -> nothing !
Now, I'm asking you...
Here some hardware/boot/tests indications :
# SCSI DECLARATION - Boot time #
scsi0 : Tekram DC390U2(T)/DC390WUF(T)/DC310U/DC310 V1.13 MAY-17-1998
scsi : 1 host.
Vendor: IOMEGA Model: ZIP 100 Rev: E.08
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 1, lun 0
Vendor: SCANNER Model: Rev: 2.02
Type: Scanner ANSI SCSI revision: 01 CCS
Detected scsi generic sgb at scsi0, channel 0, id 6, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1
GB]
sda: Write Protect is off
# Scanner verification by scanimage - MUSTEK 12000SP #
scanimage -L
device `pnm:0' is a Noname PNM file reader virtual device
device `pnm:1' is a Noname PNM file reader virtual device
device `mustek:/dev/scanner' is a Mustek C06 S12IDW flatbed scanner
device `mustek:/dev/sg1' is a Mustek C06 S12IDW flatbed scanner
# Processor (AMD K6, 200MHz) - Linux ( SuSe 5.3)#
uname -a
Linux rotondo 2.0.35 #1 Sun Dec 13 21:39:02 CET 1998 i586 unknown
# Memory and Swap (RAM = 64 Mo and SWAP = 64 Mo)#
Calibrating delay loop.. ok - 400.59 BogoMIPS
Memory: 63196k/65536k available (748k kernel code, 384k reserved, 1208k
data)
Adding Swap: 36284k swap-space (priority -1)
Adding Swap: 33228k swap-space (priority -2)
# SCSI controler #
DC-390F (Ultra-Wide SCSI-3)
# Errors messages when scanimage (SANE)- in color #
scanimage -d mustek:/dev/sg1 --mode color -v >mon_truc.ppm
scanimage: scanning image of size 153x207 pixels at 24 bits/pixel
scanimage: acquiring RGB frame
scanimage: min/max graylevel value = 255/0
scanimage: sane_read: Out of memory
# Errors messages when xscanimage (SANE)- in color #
Error during read : Out of memory
Thank you !
Email : btqy@infini.fr
--------------53E718F1CC017124841C9F13
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
Mustek SE 12000SP, only in gray with SANE on SuSE 5.3 ?
I've just had a scanner - Mustek SE 12000SP (C06 S12IDW flatbed scanner)
- and I've plugged it on my SCSI-3 controller, a Tekram DC-390F.
When I use SANE (new version 1.0 - SuSE rpm), I can work only in Gray
or
Lineart at the lowest resolution : 60 dpi.
If I try something else, I've got the following messages :
Error during read : Out of memory - (xscanimage in Xwindow)
or
sane_read: Out of memory - (scanimage in console mode)
My computer is fitted with 64 Mo SDRAM and 64 Mo of SWAP...
The scanner works fine under Micro$oft 95 but not on SuSE Linux 5.3
!
Does anyone has THE solution ?
I tried the following things :
1 - asking Dejanews -> nothing !
2 - reading SANE documentation with different tests on
/etc/sane.d/mustek.conf -> nothing !
3 - try swapoff -a -> nothing !
Now, I'm asking you...
Here some hardware/boot/tests indications :
# SCSI DECLARATION - Boot time #
scsi0 : Tekram DC390U2(T)/DC390WUF(T)/DC310U/DC310 V1.13 MAY-17-1998
scsi : 1 host.
Vendor: IOMEGA Model: ZIP 100
Rev: E.08
Type: Direct-Access
ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 1, lun 0
Vendor: SCANNER Model:
Rev: 2.02
Type: Scanner
ANSI SCSI revision: 01 CCS
Detected scsi generic sgb at scsi0, channel 0, id 6, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1
GB]
sda: Write Protect is off
# Scanner verification by scanimage - MUSTEK 12000SP #
scanimage -L
device `pnm:0' is a Noname PNM file reader virtual device
device `pnm:1' is a Noname PNM file reader virtual device
device `mustek:/dev/scanner' is a Mustek C06 S12IDW flatbed scanner
device `mustek:/dev/sg1' is a Mustek C06 S12IDW flatbed scanner
# Processor (AMD K6, 200MHz) - Linux ( SuSe 5.3)#
uname -a
Linux rotondo 2.0.35 #1 Sun Dec 13 21:39:02 CET 1998 i586 unknown
# Memory and Swap (RAM = 64 Mo and SWAP = 64 Mo)#
Calibrating delay loop.. ok - 400.59 BogoMIPS
Memory: 63196k/65536k available (748k kernel code, 384k reserved, 1208k
data)
Adding Swap: 36284k swap-space (priority -1)
Adding Swap: 33228k swap-space (priority -2)
# SCSI controler #
DC-390F (Ultra-Wide SCSI-3)
# Errors messages when scanimage (SANE)- in color #
scanimage -d mustek:/dev/sg1 --mode color -v >mon_truc.ppm
scanimage: scanning image of size 153x207 pixels at 24 bits/pixel
scanimage: acquiring RGB frame
scanimage: min/max graylevel value = 255/0
scanimage: sane_read: Out of memory
# Errors messages when xscanimage (SANE)- in color #
Error during read : Out of memory
Thank you !
Email : btqy@infini.fr