Hello,
I brought a Musten 1200ub scanner (which
has sane backend support). I have linux kernel-2.2.16,
and when i load the usb-uhci module, these are the
messages i get:
--------------------------------
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c:
$Revision: 1.232 $ time 16:53:56 Aug 22 2000
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c: High
bandwidth mode enabled
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c: USB
UHCI at I/O 0xcc00, IRQ 10
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c:
Detected 2 ports
May 29 15:27:40 rdu25-8-140 kernel: usb.c: new USB bus
registered, assigned bus number 1
May 29 15:27:40 rdu25-8-140 kernel: usb.c: USB new
device connect, assigned device number 1
May 29 15:27:40 rdu25-8-140 kernel: hub.c: USB hub
found
May 29 15:27:40 rdu25-8-140 kernel: hub.c: 2 ports
detected
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c: USB
UHCI at I/O 0xc800, IRQ 10
May 29 15:27:40 rdu25-8-140 kernel: usb-uhci.c:
Detected 2 ports
May 29 15:27:40 rdu25-8-140 kernel: usb.c: new USB bus
registered, assigned bus number 2
May 29 15:27:40 rdu25-8-140 kernel: usb.c: USB new
device connect, assigned device number 1
May 29 15:27:40 rdu25-8-140 kernel: hub.c: USB hub
found
May 29 15:27:40 rdu25-8-140 kernel: hub.c: 2 ports
detected
May 29 15:27:41 rdu25-8-140 kernel: usb.c: USB new
device connect, assigned device number 2
May 29 15:27:41 rdu25-8-140 kernel: usb.c: This device
is not recognized by any installed USB driver.
May 29 15:27:41 rdu25-8-140 kernel: hub.c: already
running port 1 disabled by hub (EMI?), re-enabling...
May 29 15:27:41 rdu25-8-140 kernel: usb.c: USB
disconnect on device 2
May 29 15:27:42 rdu25-8-140 kernel: usb.c: USB new
device connect, assigned device number 2
May 29 15:27:42 rdu25-8-140 kernel: usb.c: This device
is not recognized by any installed USB driver.
May 29 15:27:59 rdu25-8-140 kernel: scanner.c:
open_scanner(0): Unable to access minor data
---------------------------------------------
I have the following modules loaded:
usb-uhci, scanner, and usbcore.
USB is seeing the device, as when i do a
`cat /proc/bus/usb/devices`, i get one of the lines
as :
-------------------------------------------
P: Vendor=055f ProdID=0006 Rev= 1.00
-------------------------------------------
Which happens to be Mustek's vendor id, and prod-id=
1200ub scanner.
I have installed the sane backend provided by Mustek,
and when i do a scnaimge --list-devices, it gives the
following message:
----------------------------------------
entering sane_get_devices.
----------------------------------------
and when i do a scanimage --test, it gives the
following output:
----------------------------------------
entering sane_get_devices.
scanimage: no SANE devices found
----------------------------------------
could anyone help in findind out what is wrong. any
help or pointers would be helpful.
Thanks.
takk.
__________________________________________________
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
This archive was generated by hypermail 2b29 : Tue May 29 2001 - 12:35:31 PDT