Hi Peter,
Thanks for the tip. This works. I can now use my scanner again.
Rogier
Peter Kirchgessner wrote:
>
> Hi Rogier,
>
> you have another HP device in your SCSI-chain. Maybe this could cause
> the problem. Try to remove the line "scsi HP" from the file
> /usr/local/etc/sane.d/hp.conf and only have the line
> /dev/sg0 in it.
>
> --Peter
>
> Rogier Stam wrote:
> >
> > Hi Peter,
> >
> > Thanks for replying to my email. I really cannot find what I'm doing
> > wrong. I've added an extract from the /var/log/messages file. These
> > messages appear directly after the start of xscanimage (with or without
> > any options specified, it does not matter), just before it segfaults.
> > Mar 31 21:31:49 Drizzt kernel: sym53c876-0-<3,*>: target did not report
> > SYNC.
> > Mar 31 21:31:52 Drizzt kernel: sym53c876-0-<6,*>: asynchronous.
> >
> > I've also added the /proc/scsi/scsi file, so you can see what's where :
> >
> > Attached devices:
> > Host: scsi0 Channel: 00 Id: 03 Lun: 00
> > Vendor: HP Model: C5110A Rev: 3701
> > Type: Processor ANSI SCSI revision: 02
> > Host: scsi0 Channel: 00 Id: 04 Lun: 00
> > Vendor: IOMEGA Model: ZIP 100 Rev: J.03
> > Type: Direct-Access ANSI SCSI revision: 02
> > Host: scsi0 Channel: 00 Id: 06 Lun: 00
> > Vendor: HP Model: C1533A Rev: 9608
> > Type: Sequential-Access ANSI SCSI revision: 02
> > Host: scsi1 Channel: 00 Id: 04 Lun: 00
> > Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.10
> > Type: CD-ROM ANSI SCSI revision: 02
> > Host: scsi1 Channel: 00 Id: 05 Lun: 00
> > Vendor: PHILIPS Model: CDD3600 CD-R/RW Rev: 2.00
> > Type: CD-ROM ANSI SCSI revision: 02
> > Host: scsi1 Channel: 00 Id: 06 Lun: 00
> > Vendor: IBM Model: DDRS-39130D Rev: DC1G
> > Type: Direct-Access ANSI SCSI revision: 02
> >
> > You can find the output generated by hpinq in the attached file
> > (hpinq.out). It seems to work normally, that's the odd thing.
> > The output from the find-scanner tool also suggests that the scanner can
> > be found by sane....
> >
> > find-scanner: found processor "HP C5110A 3701" at device /dev/scanner
> > find-scanner: found processor "HP C5110A 3701" at device /dev/sg0
> > find-scanner: found processor "HP C5110A 3701" at device /dev/sga
> >
> > Another odd thing I found (I don't know if it's related), is when I run
> > the scsi_info tool on /dev/sga. The result is the following :
> >
> > SCSI_ID="0,3,0"
> > MODEL="Direct-A "
> > FW_REV="SCSI"
> >
> > That should say something like what can be found in the /proc/scsi/scsi
> > file as far as I know, which would make me expect that model would be
> > C5110A instead of Direct-A .....
> >
> > Thanks so far.
> >
> > Rogier
> >
> > Peter Kirchgessner wrote:
> > >
> > > Hi Rogier,
> > >
> > > dou you get any other messages before the segmentation fault ? At what
> > > action do you get it ? Start of xscanimage, start of preview scan ?
> > > If you can run the hpinq-tool, the communication with the scanner should
> > > be ok.
> > >
> > > Rogier Stam wrote:
> > > >
> > > > Hi,
> > > >
> > > > Has anybody seen this problem before ? I have been trying to get the
> > > > Symbios Logic 22801 Dual channel controller with the HP Scanjet 5P on
> > > > channel 0 to work. All I get when I start xscanimage or scanimage is
> > > > that I got a Segmentation Fault. When I look during boot time I can see
> > > > that the kernel can find the Scanner, as can the find-scanner tool and
> > > > the hpinq tool. I also get a target did not report SYNC message in my
> > > > /var/log/messages file.
> > > >
> > > > I'm using kernel 2.2.13, but the problem also occurs on 2.2.14, 2.2.3,
> > > > 2.2.5 and 2.2.9 so I don't think that's the problem. Should it help, the
> > > > linux distribution I'm using is Slackware 7.0. I'm currently using sane
> > > > v1.02, but the problem also occurs on sane v1.01. I'm currently using
> > > > the Symbios SCSI driver, but the problem also occurs when using the
> > > > NCR8XX SCSI driver in the kernel.
> > > >
> > > > I've checked cable lengths and termination, and it should not cause any
> > > > problems.....
> > > >
> > > > I hope you can help me.
> > > >
> > > > Regards,
> > > >
> > > > Rogier Stam
> > > >
> > > > --
> > > > Source code, list archive, and docs: http://www.mostang.com/sane/
> > > > To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
> > >
> > > --
> > > Peter Kirchgessner
> > > WWW: http://www.kirchgessner.net
> > > e-mail: peter@kirchgessner.net
> > >
> > > --
> > > Source code, list archive, and docs: http://www.mostang.com/sane/
> > > To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
> >
> > ------------------------------------------------------------------------
> > Name: hpinq.out
> > hpinq.out Type: unspecified type (application/octet-stream)
> > Encoding: base64
>
> --
> Peter Kirchgessner
> WWW: http://www.kirchgessner.net
> e-mail: peter@kirchgessner.net
>
> --
> Source code, list archive, and docs: http://www.mostang.com/sane/
> To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
This archive was generated by hypermail 2b29 : Sun Apr 02 2000 - 00:36:00 PST