Hey there.
I have a UMAX Astra 610S scanner, which is listed as being supported by
sane, but I am unable to get it to work and think that I'm just missing
something easy to fix. So, I am asking if anyone would know what is
wrong based on what I do know.
[root@dilophosaur /dev]# insmod aha152x aha152x=0x140,11,6,1
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x0: vital data: PORTBASE=0x140, IRQ=11, SCSI ID=6,
reconnect=enabled,
parity=enabled, synchronous=disabled, delay=100, extended
translation=disabled
aha152x: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 1.7 $
scsi : 1 host.
Vendor: UMAX Model: Astra 610S Rev: V1.3
Type: Scanner ANSI SCSI revision: 02
Vendor: IOMEGA Model: ZIP 100 Rev: J.02
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 5, lun 0
SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1
GB]
sda: Write Protect is on
sda: sda4
--- To me, it seems that the adaptor's modules loaded correctly. The adaptor is just a generic aha152x adaptec card.Next, I check everything is truly connected. --- [root@dilophosaur /root]# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 02 Lun: 00 Vendor: UMAX Model: Astra 610S Rev: V1.3 Type: Scanner ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 05 Lun: 00 Vendor: IOMEGA Model: ZIP 100 Rev: J.02 Type: Direct-Access ANSI SCSI revision: 02 --- Looks good to me.
Next, I set the UMAX debug level and try to see if SANE will see it... --- [user@dilophosaur user]$ scanimage -L [sanei_init_debug]: Setting debug level of umax to 128. [umax] sane_init [umax] This is sane-umax version 1.0 build 18 [umax] (C) 1997-2000 by Oliver Rauch [umax] EMAIL: Oliver.Rauch@Wolfsburg.DE [umax] attach_scanner: /dev/scanner [umax] attach_scanner: opening /dev/scanner [umax] attach_scanner: open failed [umax] attach_scanner: /dev/sga [umax] attach_scanner: opening /dev/sga [umax] attach_scanner: open failed [umax] attach_scanner: /dev/sgb [umax] attach_scanner: opening /dev/sgb [umax] attach_scanner: open failed [umax] sane_get_devices [umax] sane_exit --- Checking my devices.... --- [user@dilophosaur user]$ ls -l /dev/sg* lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg0 -> sga lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg1 -> sgb lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg2 -> sgc lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg3 -> sgd lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg4 -> sge lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg5 -> sgf lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg6 -> sgg lrwxrwxrwx 1 root root 3 Jan 22 19:42 /dev/sg7 -> sgh crwxrwxrwx 1 root sys 21, 0 May 5 1998 /dev/sga crwxrwxrwx 1 root sys 21, 1 May 5 1998 /dev/sgb crwxrwxrwx 1 root sys 21, 2 May 5 1998 /dev/sgc crwxrwxrwx 1 root sys 21, 3 May 5 1998 /dev/sgd crwxrwxrwx 1 root sys 21, 4 May 5 1998 /dev/sge crwxrwxrwx 1 root sys 21, 5 May 5 1998 /dev/sgf crwxrwxrwx 1 root sys 21, 6 May 5 1998 /dev/sgg crwxrwxrwx 1 root sys 21, 7 May 5 1998 /dev/sgh [user@dilophosaur user]$ ls -l /dev/scanner lrwxrwxrwx 1 root root 3 Feb 24 20:55 /dev/scanner -> sga --- Hmmm. The last bit of information I want to contribute is: --- [kyroraz@dilophosaur sane.d]$ cat umax.conf scsi UMAX * Scanner scsi LinoHell Office scsi LinoHell Office2 scsi LinoHell SAPHIR2 scsi Nikon AX-210 /dev/scanner /dev/sga /dev/sgb
-----
Anyone have any ideas? I'm running out of them tonight... The ZIP drive works perfectly, so I don't think it's the SCSI card, and the scanner detects in Windows, at least, Windows says that it's there (haven't scanned in Windows at all). I hope this is the right forum for this too. :)
Jason
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
This archive was generated by hypermail 2b29 : Thu Feb 24 2000 - 19:24:00 PST