Getting UMAX scanner to work with Future domain 1

Zot O'Connor (zot@ZotConsulting.com)
Fri, 14 Aug 1998 16:02:13 -0700

I am having problems getting my future domain controller
(old ISA) to recognize my Vista S8 scanner.

The controller worked extremely well recently, but I
replaced it when I upgraded. I have an UDS-1101 (or whatever)
working as a full SCSI under NT. I though I'd move it to Linux.

I have a jaz drive on the card too, it works.

The Scanner does not seem to report to the kernel module (it is at ID1)
Aug 14 15:19:30 eater kernel: scsi2 <fdomain>: BIOS version 2.0 at 0xca000 using
scsi id 6
Aug 14 15:19:30 eater kernel: scsi2 <fdomain>: TMC-1800 chip at 0x140 irq 15
Aug 14 15:19:30 eater kernel: scsi2 : Future Domain TMC-16x0 SCSI driver, versio
n 5.44
Aug 14 15:19:30 eater kernel: scsi : 1 host.
Aug 14 15:19:30 eater kernel: Vendor: iomega Model: jaz 1GB Rev:
H.62
Aug 14 15:19:30 eater kernel: Type: Direct-Access ANSI
SCSI revision: 02
Aug 14 15:19:30 eater kernel: Detected scsi removable disk sda at scsi2, channel
0, id 5, lun 0
Aug 14 15:19:30 eater kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
2091050 [1021 MB] [1.0 GB]
Aug 14 15:19:30 eater kernel: sda: Write Protect is off
Aug 14 15:19:30 eater kernel: sda: sda4

[root@eater /root]# cat /proc/scsi/fdomain/2
Future Domain TMC-16x0 SCSI driver, version 5.44
[root@eater /root]# cat /proc/scsi/scsi
Attached devices:
Host: scsi2 Channel: 00 Id: 05 Lun: 00
Vendor: iomega Model: jaz 1GB Rev: H.62
Type: Direct-Access ANSI SCSI revision: 02

Yet when I scanimage --list-devices I get some recognition:

Scanlist
[umax] attach_scanner: opening /dev/sga
[umax] init
[umax] initialize_values
[umax] identify_scanner
[umax] do_inquiry
[umax] check condition sense handler
[umax] check condition sense: ILLEGAL REQUEST
[umax] -> no error
[umax] -> illegal field in CDB
[umax] check condition sense handler
[umax] check condition sense: ILLEGAL REQUEST
[umax] -> no error
[umax] -> illegal field in CDB
[umax] attach_scanner: scanner-identification failed
[umax] attach_scanner: opening /dev/sgb
[umax] attach_scanner: open failed
[umax] attach_scanner: opening /dev/sgb
[umax] attach_scanner: open failed
[umax] attach_scanner: opening /dev/sge
[umax] attach_scanner: open failed
[umax] attach_scanner: opening /dev/sda
[umax] init
[umax] initialize_values
[umax] identify_scanner
[umax] do_inquiry
[umax] check condition sense handler
[umax] invalid sense key => handled as DEVICE BUSY!
[umax] check condition sense handler
[umax] invalid sense key => handled as DEVICE BUSY!
[umax] attach_scanner: scanner-identification failed
[umax] attach_scanner: opening /dev/scanner
[umax] attach_scanner: open failed

I have had parity errors with this card and an old NEC Cdrom.
I though that was fixed now. Any ideas?

-- 
Zot O'Connor


www.ZotConsulting.com
www.WhiteKnightHackers.com





--
Source code, list archive, and docs: http://www.mostang.com/sane/
To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com