> Tried latest sane distribution (0.70), scanner does the calibration then
> stops, mtekscan-0.2 works (when I comment out check of vender-id).
> Output generated:
> P6
> # SANE data follows
> 2 0
> 255
>
> Error output:
> [sanei_init_debug]: Setting debug level of microtek to 128.
> [microtek] sane_init: MICROTEK says hello! (v0.4)
> [microtek] sane_init: config- #Uncomment the following if you are tired of sng the dump of the
> [microtek] sane_init: config- # scanner INQUIRY every time the backend startp...
> [microtek] sane_init: config- #nodump
> [microtek] sane_init: config- /dev/scanner
> [microtek] attach_scanner: /dev/scanner
> [microtek] attach_scanner: opening /dev/scanner
> [microtek] attach_scanner: sending INQUIRY
> [microtek] id_microtek...
> [microtek] parse_inquiry...
> [microtek] dump_inquiry...
> ========== Scanner Inquiry Block ==========
> 06 31 13 01 5b 16 00 00 20 20 20 20 20 20 20 20
> 53 63 61 6e 6e 65 72 20 36 30 30 20 20 20 20 20
> 31 2e 39 31 53 43 53 49 20 46 2f 57 56 33 2e 34
> 20 43 54 4c 35 33 38 30 03 4f 8c c5 03 ee 66 03
> 00 03 01 00 00 03 00 01 0e 0e 01 05 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff
>
> ========== Scanner Inquiry Report ==========
> ===== Scanner ID...
> Device Type Code: 0x06
> Model Code: 0x66
> Vendor Name: ' ' Model Name: 'Scanner 600 '
> Firmware Rev: '1.91'
> SCSI F/W version: 3.1 Scanner F/W version: 1.3
> Response data format: 0x01
> ===== Imaging Capabilities...
> Modes: Lineart Halftone Gray Color (OnePass)
> Resolution Step Sizes: 1% 5% Expanded Resolution Support? yes(but says no)
> Supported Bits Per Sample: 4 8
> Max. document size code: 0x03
> Max. document size: 8.500000 x 13.000000 inches
> Frame units: pixels 1/8"'s
> # of built-in halftones: 12 Downloadable patterns? Yes
> Data Compression:
> Contrast Settings: 14 Exposure Settings: 14
> Adjustable Shadow/Highlight? yes Adjustable Midtone? yes
> Digital brightness/offset? yes
> Gamma Table Size: 256 entries of 1 bytes (max. value: 255)
> ===== Source Options...
> Feed type: flatbed ADF support? yes
> Document Feeder Support? yes Feeder Backtracking? yes
> Feeder Installed? no Feeder Ready? no
> Transparency Adapter Installed? no
> Fast Color Prescan? no
> Selectable Transfer Format? no
> Color Transfer Sequence: line-by-line, non-sequential with headers
> Three pass scan support? no
> ModeSelect-1 and ModeSense-1 Support? yes
> Can Disable Linearization Table? no
> Can Disable Start-of-Scan Recalibration? yes
>
>
> [microtek] attach_scanner: happy.
> [microtek] sane_init: config-
> [microtek] sane_open
> [microtek] sane_open: gonna init opts: [microtek] init_options...
> [microtek] init_options: quant yes
> [microtek] init_options: done.
> [microtek] sane_control_option (opt=0,act=0,val=0xbffff8a8,info=(nil))
> [microtek] sane_control_option (opt=0,act=0,val=0xbffff868,info=(nil))
> [microtek] sane_get_option_descriptor (0)...
> [microtek] sane_get_option_descriptor (1)...
> [microtek] sane_get_option_descriptor (2)...
> [microtek] sane_get_option_descriptor (3)...
> [microtek] sane_get_option_descriptor (4)...
> [microtek] sane_get_option_descriptor (5)...
> [microtek] sane_get_option_descriptor (6)...
> [microtek] sane_get_option_descriptor (7)...
> [microtek] sane_get_option_descriptor (8)...
> [microtek] sane_get_option_descriptor (9)...
> [microtek] sane_get_option_descriptor (10)...
> [microtek] sane_get_option_descriptor (11)...
> [microtek] sane_get_option_descriptor (12)...
> [microtek] sane_get_option_descriptor (13)...
> [microtek] sane_control_option (opt=13,act=0,val=0x8052cb0,info=(nil))
> [microtek] sane_get_option_descriptor (14)...
> [microtek] sane_control_option (opt=14,act=0,val=0x8052cb4,info=(nil))
> [microtek] sane_get_option_descriptor (15)...
> [microtek] sane_get_option_descriptor (16)...
> [microtek] sane_get_option_descriptor (17)...
> [microtek] sane_get_option_descriptor (18)...
> [microtek] sane_get_option_descriptor (19)...
> [microtek] sane_get_option_descriptor (20)...
> [microtek] sane_get_option_descriptor (21)...
> [microtek] sane_get_option_descriptor (22)...
> [microtek] sane_get_option_descriptor (23)...
> [microtek] sane_get_option_descriptor (24)...
> [microtek] sane_get_option_descriptor (25)...
> [microtek] sane_get_option_descriptor (26)...
> [microtek] sane_get_option_descriptor (27)...
> [microtek] sane_get_option_descriptor (28)...
> [microtek] sane_get_option_descriptor (29)...
> [microtek] sane_get_option_descriptor (30)...
> [microtek] sane_get_option_descriptor (31)...
> [microtek] sane_get_option_descriptor (32)...
> [microtek] sane_get_option_descriptor (33)...
> [microtek] sane_control_option (opt=11,act=0,val=0xbffff864,info=(nil))
> [microtek] sane_control_option (opt=12,act=0,val=0xbffff864,info=(nil))
> [microtek] sane_control_option (opt=11,act=0,val=0xbffff8a4,info=(nil))
> [microtek] sane_get_option_descriptor (13)...
> [microtek] sane_control_option (opt=13,act=1,val=0xbffff8a0,info=0xbffff860)
> [microtek] sane_control_option (opt=12,act=0,val=0xbffff8a4,info=(nil))
> [microtek] sane_get_option_descriptor (14)...
> [microtek] sane_control_option (opt=14,act=1,val=0xbffff8a0,info=0xbffff860)
> [microtek] sane_start...
> [microtek] sane_get_parameters...
> [microtek] sane_get_parameters: res_code = 16 (10)
> [microtek] sane_get_parameters: dots_per_mm: 3.937008
> [microtek] sane_get_parameters: units_per_mm: 23.622047
> [microtek] sane_get_parameters: lines: 0
> [microtek] .wait_ready 3...
> [microtek] .mode_select_1 3...
> [microtek] .mode_sense_1...
> [microtek] .accessory...
> [microtek] .mode_sense 3...
> [microtek] .scanning_frame 3...
> [microtek] .scanning_frame: in- 0,0 0,0
> [microtek] .scanning_frame: out- 0,0 0,0
> [microtek] .download_gamma...
> [microtek] .mode_select 3...
> [microtek] .mode_select: pap_len: 7800
> [microtek] .mode_sense 3...
> [microtek] .wait_ready 3...
> [microtek] .start_scan...
> [microtek] .wait_ready 3...
> [microtek] .get_scan_status 3...
> [microtek] get_scan_status(6): 0, 4, 0
> [microtek] > 0 4 0 0 0 0
> [microtek] sane_start: spacing = 2, holdsize = 32768
> [microtek] Scan Param:
> [microtek] pix bpl: 6 hdr bpl: 6 ppl: 2
> [microtek] lines: 0 planes: 3
> [microtek] dest bpl: 6 dest ppl: 2 aspect: 1.000000
> [microtek] sane_get_parameters...
> [microtek] sane_read...
> [microtek] end_scan...
> [microtek] .stop_scan...
> [microtek] sane_cancel...[microtek] sane_close...
> [microtek] sane_exit...
> [microtek] sane_exit: MICROTEK says goodbye.
>
>
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com